• 繁體中文
  • 產品介紹
    若您有任何詢問?請與我們聯繫,我們會盡快與您連絡。
    Home > Products Index > Dehumidifying Dryer > Honeycom Dehumidifying Dryer > RD Series
    Honeycom Dehumidifying Dryer : RD系列

    Honeycom Dehumidifying Dryer

    RID

    功能特點
    規格表


    Features


    • Top-quality, Japanese honeycomb wheel for prolonged use without leaving residue to ensure cleanliness
    • Dew point remains below -40° C steadily
    • Intelligent, microcomputer-based system plus PID temp control
    • Filter, cooler and electric heater are all of SUS304
    • Exterior, flush-mounted filter for dehumidified and regenerated air
    • Easily detachable SUS304 cooler is easy to clean even after handling oil-based plastic
    • Phase-reversal, failure, abnormal operation, motor overload, and over-temperature protection

    • How to choose the appropriate model:
      a. At 60hz, according to the hourly feeding quantity of the model, the most appropriate model can be identified by comparing the raw material and drying function;
      b. At 50hz, according to the hourly feeding quantity of the model, the most appropriate model can be identified by comparing the raw material and 80-85% drying function;
    • This indicates the drying capacity of temperature at 20℃ and 65% RH (relative humidity) and the material water content below 200PPM
    • RH (relative humidity): the ratio of water pressure (PW) and saturated water pressure (Pws) at the specific temperature %, RH=PW/PWS×100%
    • Td (Temperature of dew): the temperate at which the saturated water in the air reaches the state of saturation to produce liquid water on the surface.
    • The temperature of Pw=Pws, namely, Td.
    • If the Td is lower than the environmental temperature, it means the possibility of condensation/dewing is lower, namely, the air is drier.


      Option


      ▲ Dew point hygrometer ▲ HEPA filter ▲ Hydro tracer for plastics  
      ▲ Tin blow insulation dryer ▲ Double silicone duct and piping parts/td ▲ RS485 communications interface  
      ▲ TIMER      





    Specifications
  • Detailed specifications >>

  • Model
    Air flow
    Drying blower 60HZ
    50HZ
    Regenerative blower 60HZ
    50HZ
    Regenerative heater
    Connection piping
    Regenerative air outlet
    Process Filter
    Regenerative Filter
    Cooling water piping
    Total load
    Dimension
    Approx. Weight
    RD-50 RD-100 RD-200 RD-300 RD-400 RD-700 RD-1000
    CMH 50 100 200 300 400 700 1000
    kw 0.5 0.85 1.9 2.6 3.7 7.5 11
    kw 0.4 0.75 1.75 2.2 3.4 6.3 9.0
    kw 0.2 0.2 0.5 0.85 0.85 2.6 3.7
    kw 0.18 0.18 0.4 0.75 0.75 2.2 3.4
    kw 3 4.5 6 10 10 15 22
    Inch 1.5 2.5 2.5 3 3.5 4.5 6.5
    Inch 1.5 2 2 2 2.5 3 3.5
    OD. x L mm 125 x 170 155 x 190 155 x 190 234 x 255 234 x 255 250 x 300 250 x300 x 2
    OD. x L mm 125 x 170 155 x 190 155 x 190 234 x 255 234 x 255 234 x 255 250 x 300
    Inch 3/8 3/8 1/2 3/4 3/4 1 1 1/4
    LPM 12 12 20 35 35 60 90
    kg/cm2 Over 1~1.5 kg/cm2
    kw 3.7 5.55 8.4 13.5 14.6 25.1 36.7
    W 55 55 55 75 75 115 120
    D 80 80 100 115 115 150 150
    H 146 146 146 176 176 206 223
    Kg 180 200 250 300 350 500 600

    ※We reserve the right to change specifications without prior notice.


    1. 如何選擇適當的Model:

    A. 60HZ時依成型機每小時吃料量,對照原料及乾燥功能即可尋得最適當之Model。

    B. 50HZ時依成型機每小時吃料量,對照原料及80-85%乾燥能力即可尋得最適當之Model。

    2. 本表為20ºC大氣溫度及65%相對濕度,料含水率低於200PPM之乾燥能力。

    3. 相對濕度(RH):指在特定溫度下的水汽壓(Pw)和飽和水汽壓(Pws)之比。%RH= PW/PWS x 100%

    4. 露點溫度(Td):指空氣中飽和水汽達到飽和狀態,在平面表面產生純液態水時的溫度。

    5. 此時Pw=Pws的溫度,即為露點溫度(Td)。

    6. 露點溫度越小於環境溫度,就意味著越小的結露可能,也就意味著空氣越乾燥。

    乾燥能力對照表Comparison Table for Drying Capacity

    原料Material 乾燥溫度 °C

    Drying temperature

    乾燥時間 HR

    Drying time

    RD-50 RD-100 RD-200 RD-300 RD-400 RD-700 RD-1000
    ABS 80-90 2-3 38 63 126 189 252 503 629
    IONOMOER(SURLYN) 50 3-4 33 55 109 164 219 437 546
    LCP 150 3-4 20 33 67 100 133 267 333
    PA6 / 6.6 / 6.10 / 6.12 80-100 4-6 23 38 77 115 153 307 383
    PA 11/12 80 4-5 18 30 61 91 121 242 303
    PBT 130-140 3-4 19 31 62 93 123 247 309
    PC 120 3 29 49 97 146 194 388 485
    PC+ABS 100 3-4 31 52 103 155 206 412 515
    PEEK 150 3 27 45 90 135 180 360 450
    PEI 150 3-4 29 48 95 143 190 381 476
    PES 160 4 23 38 77 115 153 307 383
    PET 160 4-6 18 29 59 88 117 235 293
    PETG 66 4-5 31 52 105 157 209 419 524
    PI 120 2 31 52 105 157 209 419 524
    PMMA 80 3 33 55 110 165 220 440 549
    POM 90-100 2 32 54 108 162 216 432 541
    PPO 110-120 2 28 46 93 139 185 370 463
    PPS 140 3-4 28 46 93 139 185 370 463
    PSU 120-130 3-4 33 55 109 164 219 437 546
    PU 90 3-4 23 39 78 117 156 311 389
    TPU 90-110 2-3 29 48 97 145 193 386 483

    ※ We reserve the right to change specifications without prior notice.

    濕度及含水率對照表

    含水率
    Moisture content
    相對濕度
    Relative humidity
    露點溫度
    Relative humidity
    PPM % % °C °F
    38.96 0.0038 0.169 -50 -58
    127.50 0.0127 0.553 -40 -40
    337.76 0.0377 1.640 -30 -22
    1025.00 0.1025 4.440 -20 -4
    2573.68 0.2573 11.150 -10 +14
    6027.63 0.6027 26.120 0 +32
    12117.10 1.2117 52.520 +10 +50
    23072.37 2.3072 100.000 +20 +68

    A-MAX SCIENCE CORP
    T: +886-4-22778819 / F: +886-4-22776898 / info@a1-max.com.tw
    關於A-MAX 產品介紹 A-MAX新聞 線上型錄